Parts for Lg WKE100HVA/00: Cabinet & Door Assy : Washer Parts

Complete drum assembly for LG dryers. Includes inner drum with front and rear seals pre-installed. Replace if cracked, broken, or damaged from wear.

Drum bearing bushing for washers. Installs between drum and bearing assembly. Replace if cracked, worn, or missing to restore proper drum support.

Fix a washer that won't drain or makes grinding noises with this drain pump assembly. Includes pump, housing, filter, and drain hose for complete repair.

Fix excessive noise, wobbling, or vibration in your laundry center with this drum mounting bolt assembly. Secures the drum to its suspension bracket.

Shipping bolt for laundry centers and washers. Secures the drum during transport. Replace if lost, damaged, or missing after installation or moving.

Shipping bolt for laundry center and washer installations. Secures internal components during transport. Replace if bolt is missing, stripped, or damaged.

Dryer not heating or taking too long to dry? The heating element generates heat for drying. Front panel removal required. Video guide available.

This bracket is a replacement mounting bracket used to secure components inside the appliance, restoring proper alignment and support so parts stay fixed and operate correctly. What it does:

• Provides structural support for internal components to prevent shifting or vibration
• Secures panels or assemblies to maintain correct alignment during operation
• Helps stop rattling or loose parts that can cause noise or wear
• Fits into the original mounting locations to restore factory stability

• One replacement mounting bracket

• Disconnect power and unplug the appliance before beginning any repair
• Retain all original fasteners; use only the specified screws/bolts for secure mounting
• Inspect surrounding components for damage and replace any worn fasteners or clips as needed

Secures the heating element assembly inside your dryer drum housing. Replace if bracket is bent, cracked, or missing to properly support the heater unit.

Interior drum baffle lifts and tumbles clothes during drying. Replace if cracked, broken, or detached from drum wall. Mounts with screws to drum exterior.

Washer won't spin or makes grinding noises? The motor rotor bolt secures the rotor to the motor shaft. Requires a 17mm socket for installation.

Replacement cabinet cover panel for laundry center units. Restores exterior appearance when original is cracked, dented, or damaged. Direct fit.

Replace your laundry center's damaged parts assembly to restore proper operation. Factory replacement component installs in-line with existing parts.

Connects the motor to the drum so it can tumble. Replace if the drum won't spin, makes squealing noises, or clothes aren't drying. Confirm fit by model number.

Dryer not heating or takes multiple cycles to dry? This hi-limit thermal fuse cuts power when temps exceed safe limits. Moderate DIY repair, about 1 hour.

Secures the outer door boot seal to prevent water leaks. Replace if damaged, rusted, or losing tension. Includes tensioning spring. Verify fit.

Hinge bracket for laundry center and washer units. Replaces broken, cracked, or worn brackets that support the door hinge assembly during operation.

Replace broken or loose hardware connections in your laundry center with this complete parts assembly. Restores proper fit and function to worn components.

Replace your dryer drum seal when clothes take longer to dry or you notice lint buildup. Maintains heat efficiency and prevents air leaks. Confirm fit with your model number.

Dryer won't heat or overheating? This hi-limit thermostat regulates temperature and prevents overheating. 10-minute DIY fix with video guide.

Secures the stator to the motor assembly in your washer. Replace if bolt is stripped, spinning freely, or missing to restore proper motor stability.

Thread-forming fastener that secures panels, brackets, and internal components. Replace this screw if it's missing, stripped, or damaged during repairs.

Fix washer control errors, intermittent power, or non-working components with this wiring harness. Restores reliable electrical connections and function.

Parts assembly for dryers and laundry centers. Replace this component if damaged, broken, or missing to restore proper structure and function.

Replacement handle for laundry center doors. Installs on front panel for opening and closing access. Needed when original is cracked, broken, or missing.

Fix no hot water, slow filling, or screaming noise during fill. This washer water inlet valve controls water flow into the tub. Moderate DIY repair.

Fix a washer that won't fill, fills slowly, or leaks at the water connection. This inlet valve controls water flow into the tub. Easy DIY repair.

Fix water leaking from vent pipe with this washer float assembly. Prevents overflow and controls suds. Moderate DIY repair with video guide available.

Duct assembly for dryer exhaust venting. Connects dryer to external vent. Replace if cracked, disconnected, or missing for proper airflow routing.

Washer won't spin or agitate? The stator assembly generates the electromagnetic field that powers drum rotation. Moderately difficult repair.

Mounts to the washer's lower frame to secure components and maintain alignment. Replace if bracket is cracked, broken, rusted, or missing hardware.

If your dryer won't tumble or makes loud scraping noises, the drum assembly may be damaged. This inner tub holds and rotates laundry during cycles.

Replace a cracked or warped top plate panel on your laundry center. Restores appearance and protects internal components. Moderate DIY repair.

Fix unresponsive buttons, blank display, or missing cycle options with this control panel assembly. Restores touch controls and LED indicators.

Leveling leg assembly for washers and laundry centers. Installs at the base to support and level the unit. Replace if cracked, broken, or missing.

LED light illuminates your dryer drum for easy viewing during operation. Replace when light dims, flickers, or burns out. Verify fit with your model.

Fix fabric softener leaking or not dispensing properly with this washer dispenser cap. Seals the softener compartment to prevent drips and residue.

Seals siphon/drain connection to prevent leaks and odors. Replace if worn, cracked, or leaking. Confirm fit with your washer model number.

Fix leaking from under the detergent dispenser with this washer dispenser box. Solves cracks or breaks that compromise the dispenser structure.

Drum support roller assembly for dryers. Installs inside the cabinet to support the drum during rotation. Replace when worn, flat-spotted, or broken.

If your refrigerator isn't cooling properly or displays error codes, the control board may have failed. This part restores factory settings and functions.

Secures the door hinge assembly to the dryer cabinet. Replace if your bracket is cracked, bent, or broken to restore proper door alignment and support.

Fix water pooling inside your laundry center with this drain hose cap. Seals the defrost drain outlet to direct meltwater properly and prevent leaks.

This replacement case is the outer housing that protects and encloses internal components, keeping them secure and helping maintain proper airflow and alignment. It restores the appliance's structural support and appearance. What it does:

• Covers and protects internal parts from dust, debris, and accidental contact
• Helps maintain component alignment and reduces movement or rattling
• Assists in directing airflow or ventilation pathways as designed
• Restores the appliance's outer appearance after damage or wear

• One replacement case

• Disconnect power before starting any repair; follow all safety precautions
• Handle with care to avoid scratching or cracking the replacement case
• Minor disassembly of adjacent panels or brackets may be required for fitment

Cabinet cover assembly for laundry center units. Replaces damaged, cracked, or worn exterior cabinet panels. Restores appearance and structure.

Captures lint and debris during drying to maintain airflow and prevent exhaust buildup. Replace when torn, cracked, or warped. Confirm fit with your model.

Replaces cracked or rotted washer vent hose that causes moisture buildup and leaks. Ensures proper air circulation to prevent mildew. Verify fit.

If your dryer door pops open during cycles or won't stay closed, this door latch assembly restores a secure closure. Easy 5-minute DIY repair.

Houses the lint filter to capture debris during drying. Replace if cracked, causing clothes to snag or tear. Confirm fit with your model number.

Connects household water supply to your washer inlet valve. Replace this hose if it's cracked, leaking, or worn to restore safe water flow during cycles.

Directs water from inlet valve to detergent dispenser in LG washers. Replace if hose is cracked, leaking, won't stay attached, or damaged from wear.

Dryer won't start or stops mid-cycle? A faulty door switch assembly prevents operation. This straightforward repair restores normal function in 30 minutes.

Secures the lint filter in proper position to prevent clothes snagging. Replace if cracked, warped, or filter sits unevenly. Confirm fit with your model.

Cover that fits over the dryer's lint filter duct area. Replace if cracked, broken, or missing to keep items from falling into the duct when filter is removed.

Replace missing or stripped taptite screws that secure panels and internal components. This thread-forming screw creates a tight hold to eliminate rattles.

Distortion spring that applies tension within the dryer mechanism. Replace if fatigued, broken, or missing to restore proper tension and assembly function.

Dryer not sensing when clothes are dry? Replace the moisture sensor bar to restore auto-dry cycles. Moderate DIY repair with video guide available.

Drain hose carries used water from washer to household drain. Replace if cracked, leaking, deteriorated, or damaged to prevent water overflow issues.

Covers unused panel or cabinet holes on your laundry center. Snaps into place for a clean, finished look. Replace if cracked, missing, or damaged.

Dryer won't auto dry or cycles run too long? This moisture sensor wire harness connects sensor bars to control. Restores accurate dry cycles. DIY-friendly.

Fix LE error codes or grinding noises during spin with this washer rotor assembly. Pairs with stator to drive drum rotation. DIY repair in 30 minutes.

Secures the moisture sensor inside your dryer drum. Replace if the holder is cracked, broken, or missing to restore proper sensor positioning and function.

Front bulkhead panel for dryer drum assembly. Mounts at the front of the drum to support rotation. Replace if cracked, warped, or damaged during repair.

Dryer door won't stay closed or pops open during cycle? This latch hook secures the door panel to prevent rattling and interruptions. Easy 10-minute fix.

Washer won't fill properly or overfills? The pressure switch monitors water levels and signals when to stop filling. Moderately easy DIY repair.

Outer door frame assembly for dryer. Replaces cracked, broken, or damaged door frames. Installs on front panel to secure door components in place.

Appliance won't power on? This power cord assembly restores electrical connection when the cord is damaged or has poor contact. Direct plug-in repair.

Fix a sagging or misaligned dryer door with this replacement hinge. Restores smooth operation and proper door seal for efficient drying performance.

If your washer won't drain or leaks water during cycles, the drain hose assembly may need replacement. This hose carries water from the tub to your drain.

Pivot hanger assembly that supports and stabilizes washer components. Replace if worn, damaged, or causing misalignment to restore smooth movement.

Inner door frame for dryer. Replace if cracked, warped, or broken. Structural component that holds door assembly together. Direct fit part.

Seals dryer door to prevent heat loss during cycles. Replace when stretched, torn, or air leaks reduce drying efficiency. Confirm fit with your model.

Secures hose connections in your washer to prevent leaks. Replace if you notice water leaking or loose hose fittings. Verify fit with your model number.

Secures hose connections to prevent leaks in your washer. Replace if corroded, rusted, or leaking around hose fittings. Confirm fit by model number.

Secures washer hoses to pumps, tubs, and drain fittings to prevent leaks. Replace when weakened, rusty, or damaged to maintain tight connections.

Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.

Noise filter assembly minimizes vibrations and reduces operational noise in your washer. Replace if experiencing excessive noise or vibrations. Verify fit with your model number before ordering.

Fix loud banging, grinding noise, or poor drying performance with a new dryer blower wheel. Restores proper airflow through drum and exhaust vent.

Hardware fasteners for dryer assembly and repairs. Includes screws, nuts, and washers to secure panels, drums, or components. Replace missing or stripped.

Fix water leaking from your washer dispenser or misdirected flow with this dispenser water guide channel. Routes water properly to prevent splashing.

Dryer not drying efficiently or making loud noise? A cracked blower housing disrupts airflow. This assembly restores proper air circulation for quiet operation.

Replacement tub to pump hose for washers. Transports water from the wash tub to the drain pump. Replace if cracked, split, leaking, or damaged from wear.

Duct assembly channels air from dryer drum to blower and exhaust. Replace if cracked, warped, or missing to restore proper airflow and prevent lint bypass.

Slide guide assembly that supports and aligns moving dryer components. Replace if cracked, broken, or worn to restore smooth tracking and operation.

Pressure sensor air chamber for washers. Connects the tub to the water level switch. Replace if cracked, clogged with detergent residue, or leaking air.

Dryer not heating properly or overheating? The thermistor monitors drum temperature and signals the control board. Moderate DIY repair.

Plastic cover that protects the lint chute guide in your dryer. Replaces cracked, broken, or missing covers to maintain proper airflow routing.

Dryer not heating or shutting off mid-cycle? A faulty blower thermostat disrupts airflow regulation. Front-access repair with basic tools in 30-60 minutes.

Protective cover shields internal wiring and electrical terminals in your dryer. Replace if cracked, broken, or missing to prevent accidental contact.

Safety cover cap for dryers and laundry centers. Protects internal components and covers exposed areas. Replace if cracked, broken, or missing.

Replace a damaged wire harness causing electrical failures, intermittent operation, or non-functional components in your laundry center. Direct fit.

If your dryer drum stopped turning, a worn motor bracket may be the cause. This bracket holds the motor and tension pulley securely in place.

Hardware screws and nuts for installing a dryer side vent kit. Replace missing or stripped fasteners when reconfiguring exhaust outlet direction.

Dryer won't spin or just hums? This drum motor assembly restores tumbling action. DIY-friendly repair takes 45-60 minutes with basic tools and video guide.

Hinge pin locks shock absorbers to the washer drum assembly. Replace if broken, worn, or when installing new shock absorbers. Installs at dampener mount.

Secures hoses, tubing, and wiring to prevent rubbing and vibration in your dryer. Replace when clips break or lines become loose. Confirm fit with your model.

Dryer won't turn off when belt breaks? This safety switch detects belt failure and shuts down operation. Direct-fit replacement, moderate DIY repair.

Maintains tension on your dryer's drum belt for smooth rotation. Replace if pulley wheel is cracked, shaft worn, or assembly moves excessively during operation.

Idler pulley maintains tension on the dryer belt. Replace if worn, cracked, or causing belt slippage. Installs between motor and drum support system.

Replacement mounting screw for dryer assemblies. Secures brackets, panels, and internal components. Order when original fastener is missing, stripped, or corroded.

Self-tapping screw secures panels, brackets, and components inside your appliance. Replace stripped, corroded, or missing screws to restore secure fit.

Stationary rack that installs inside your dryer drum to hold shoes, sweaters, and delicates that shouldn't tumble. Replace if cracked, broken, or missing.

Side venting kit for dryers. Redirects exhaust from rear to side of cabinet. Perfect when space is limited or side venting is preferred over rear.

Fix a blank or unresponsive display with this laundry center display control board. Restores touch controls and display lighting. Moderate DIY repair.

Fix washer control issues with this multi-connector wire harness. Restores electrical connections between control board and components. Direct fit.

Connects detergent dispenser to washer tub. Replace if cracked, leaking, or clogged with detergent buildup. Verify fit with your model number.

Washer tripping GFCI or breaker? Failed heater assembly causes electrical shorts. Includes sensor probe. Moderate DIY repair with basic tools.

Fix a washer that won't drain or has standing water with this drain pump motor assembly. Powers the pump to remove water during drain cycles.

Suspension spring supports and stabilizes the washer tub during wash and spin cycles. Replace if broken, snapped, or stretched to restore proper operation.

The Holder is an OEM part for LG front-loading washing machines. It is a plastic mounting bracket or suspension system that attaches to the rear of the washer tub and helps secure internal components like hoses, pulleys, and the rear bearing in place during spin cycles. Subject to force and vibration, the holder must withstand years of washing use.

Symptoms of a bad holder include: 

• Loosening or detaching internal parts leading to noise and imbalance
• Cracking or damage of the plastic bracketry 
• Bearing or tub damage from improperly secured components

Causes can be fatigue from repeated wash cycles, stress cracks from heavy loads, or material deterioration over time. Replace with this OEM LG holder to maintain drum balance and suspend components securely. It is also compatible with Sears/Kenmore front-load washers.

Fix excessive vibration, banging during spin, or washer walking across floor. This damper assembly controls drum movement. Moderate DIY repair.