Parts for Kenmore Elite 79641542210: Cabinet / Control Panel Assembly Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This rear cover is the outer housing panel that protects the appliance's internal components and helps maintain proper airflow and support. It replaces a cracked, broken, or missing rear housing panel to restore protection and fit. What it does:

• Shields motors, wiring, vents, and other internal parts from dust, debris, and accidental contact
• Helps direct airflow and maintain correct ventilation for safe operation
• Restores proper mounting points and prevents rattles from a loose or damaged back panel
• Commonly replaced when there is visible damage, missing mounting tabs, or unusual noise from the rear

• One rear cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal usually requires taking off the exterior panels and a few screws or clips; retain all fasteners for reinstallation
• Watch for sharp edges and wear protective gloves; handle internal wiring and components gently

Size: 4 3/4 inches. Used to secure the washer tub before transporting. They must be removed before using your washer.

This outer tub assembly holds wash water and supports the inner drum so the washer can agitate and spin effectively. Replacing a damaged outer tub restores a sealed wash tub and prevents leaks or excessive movement. What it does:

• Houses and seals the wash chamber so water stays inside the washer during fill, wash and spin cycles
• Provides structural support for the inner drum and basket to spin smoothly
• Prevents leaks caused by cracks, corrosion or worn mounting areas
• Helps reduce abnormal noise and vibration related to a damaged tub

• Disconnect power and water supply before starting; drain any remaining water
• This is a large, heavy assembly — two people and basic hand tools are typically needed
• May require removal of the cabinet, inner tub/basket, and related hoses or seals for access
• Inspect and replace associated seals, bearings or mounting hardware as needed

Size: 6 1/4 inches. Used to secure the washer tub before transporting. They must be removed before using your washer.

Secures the washer’s tub and basket during moving to prevent internal damage. If the originals are missing after a move, install replacements for transport and remove them before using the washer.

What it does

• Locks the tub and basket to limit movement in transit
• Helps prevent suspension damage and internal rattles while relocating
• Replaces missing, bent, or stripped transport bolts
• Useful for moves, storage, or service shipments

What’s included
One shipping bolt assembly (sold individually).

Install notes

• Unplug power and turn off water before service
• Insert through the rear panel into the designated mounting point; tighten snugly—don’t overtighten
• Do not operate the washer with shipping bolts installed; remove all bolts after placement
• Some models use multiple bolts and lengths—match count/positions to your owner’s manual

Usage tip
After removal, bag and tape the bolts to the cabinet so they’re on hand for the next move.

This door hinge bracket mounts the hinge to the washer's front cabinet, keeping the door aligned so it closes and seals properly. A bent or broken bracket can lead to door sagging, poor latching, or leaks at the door.

• Secures the door hinge to the washer's front panel/cabinet
• Supports door weight to maintain alignment
• Helps preserve proper door-to-gasket contact for sealing
• Typical symptoms: door sags or rubs, won't close/latch, or water leaks at the door

• Disconnect power and shut off water before servicing.
• Support the door before removing hinge/bracket screws to prevent strain.
• Transfer the hinge to the new bracket and reinstall using existing hardware.
• Align the door and ensure latch engagement and gasket seal before fully tightening.

This lifter assembly is the plastic baffle inside the drum that lifts and tumbles laundry as the drum turns. Replacing a cracked or missing lifter restores smooth tumbling and helps prevent fabric snags and noisy operation. What it does:

• Lifts and turns items to promote effective tumbling during cycles
• Helps distribute loads more evenly and reduce thumping
• Replaces broken, loose, or missing baffles
• Addresses symptoms like rattling, clothing snagging/tearing, or poor item movement in the drum

• 1 lifter assembly

• Disconnect power before servicing
• Work through the drum opening; remove the old lifter by releasing its locking mechanism
• Align the new lifter's tabs with the drum slots, then slide/lock it securely in place
• Verify it is firmly seated and does not wobble before running a test cycle

This drum spider supports and centers the inner tub in front-load washers. It bolts to the drum and couples to the drive shaft to keep spins smooth and balanced, reducing noise and vibration as the original wears.

• Supports and centers the inner spin basket within the outer tub
• Transfers drive power through the shaft to spin the drum
• Maintains drum alignment to help prevent rubbing and noise
• When worn: loud banging/rumbling on spin, excessive vibration, metallic scraping, unbalance/spin errors, wetter-than-normal loads

• Disconnect power and water; move the washer to a stable work area
• Access requires removing panels, the door boot, and separating the tub to lift out the inner basket
• Clean mating surfaces; install and tighten bolts in a crisscross pattern to ensure even seating
• Inspect rear tub bearings and seal while open; reassemble and run a test spin to check for leaks and vibration

This replacement bolt secures the drum spider within the washer tub assembly. Replacing worn or missing hardware helps keep the basket properly mounted to reduce wobble, vibration, and noise during spin.

• Fastens the spider to the inner wash basket
• Maintains proper alignment and balance of the basket during spin
• Use when original bolts are rusted, stripped, loose, or missing
• Symptoms include rattling, thumping, off-balance errors, or visible basket wobble

• Unplug the appliance; shut off water and remove hoses if access requires moving the unit
• Access typically requires panel removal to reach the inner basket and spider
• Replace any damaged bolts and tighten evenly in a crisscross pattern; do not overtighten
• Inspect the spider and basket for corrosion or cracks before reassembly

The Tub Bearing is an OEM part for LG washing machines. This bearing supports the washer drum, allowing it to spin smoothly during the wash and spin cycles. The tub bearing ensures the drum rotates quietly and efficiently, contributing to the overall performance and longevity of the washing machine.

Causes of a bad tub bearing can include regular wear and tear, exposure to heavy loads, or moisture and detergent residue leading to corrosion. 

Symptoms of a bad tub bearing include:

• Loud noises or grinding sounds during the spin cycle
• The washer drum not spinning properly or wobbling
• Water leaks from the bottom of the washer
• Excessive vibration or shaking during operation

This OEM LG part is also compatible with some Kenmore models.

The Tub Bearing is an OEM part for LG washing machines. It supports the washer drum, ensuring it spins smoothly and quietly during wash and spin cycles.

Common causes of a bad tub bearing include regular wear and tear from frequent use, exposure to heavy or unbalanced loads, and water damage from leaks. A faulty bearing can lead to noisy operation and reduced efficiency, potentially causing further damage to the washing machine.

Symptoms of a bad tub bearing include:

• Loud noises during the wash or spin cycles
• Excessive vibration or movement of the washer
• Difficulty in spinning or the drum not spinning at all
• Water leaks from the drum area

This OEM LG part is also compatible with Sears/Kenmore.

The Motor Rotor Bolt is an OEM part for LG washing machines. It secures the rotor to the motor shaft, playing a crucial role in the efficient functioning of the motor and ensuring the washer drum spins correctly during wash cycles.

Causes of a bad motor rotor bolt can include wear and tear from prolonged use, corrosion due to exposure to moisture, or damage from over-tightening or accidental impacts. A faulty motor rotor bolt can compromise the stability of the motor, leading to various operational issues.

Symptoms of a bad motor rotor bolt include:

• The washer drum not spinning or spinning irregularly
• Unusual noises during operation, such as banging or clunking
• The washer failing to complete cycles or stopping mid-cycle
• Visible wear or damage to the bolt or surrounding components

This OEM LG part is also compatible with Sears/Kenmore models.

The Rear Tub Gasket is an OEM part for LG washing machines. It provides a watertight seal between the rear tub and the front tub assembly, preventing water leaks during the wash and spin cycles. This gasket ensures that water remains contained within the drum, contributing to the overall efficiency and performance of the washing machine.

You should replace the rear tub gasket if it becomes worn out, cracked, or damaged. Causes of a bad rear tub gasket can include general wear and tear, mold or mildew buildup, and damage from foreign objects during washing.

Symptoms of a bad rear tub gasket include:

• Water leaking from the back of the washing machine
• Visible cracks, tears, or deformation in the gasket
• Mold or mildew buildup around the gasket area
• Unusual noises during the wash cycle indicating a loose or misaligned gasket

This OEM LG part is also compatible with certain models of Kenmore washing machines.

This balance weight is the washer drum counterweight that helps stabilize the tub during spin cycles to reduce vibration and excessive movement. It restores smoother, quieter operation when the drum is unbalanced. What it does:

• Counters the rotating drum to reduce vibration, shaking and banging during spin
• Helps maintain drum alignment for consistent spin performance
• Reduces noise caused by an imbalanced load or worn/loose weight
• Prevents excessive movement that can stress suspension components

• Disconnect power and water supply before starting any repair
• Support the tub/outer cabinet to prevent it from shifting when removing old weight
• Retain and reuse original fasteners only if in good condition; replace damaged hardware

This Screw (drawing) is a factory fastener used to secure appliance panels and components. Replacing a stripped, corroded, or missing screw restores a tight fit, reduces vibration, and helps keep assemblies correctly aligned.

• Secures panels, brackets, and mounting points as specified by the manufacturer
• Replaces screws that are lost, damaged, corroded, or stripped
• Helps address rattling, vibration, or loose-fitting parts caused by missing hardware
• Maintains proper alignment and stability of the assembly

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to its original location; start threads by hand to avoid cross-threading
• Use the correct driver; tighten snugly without over-torquing into metal or plastic
• Refer to your model's parts diagram to correct location and quantity

The Outer Door Boot Seal Clamp is an OEM part for LG washing machines. This clamp secures the outer door boot seal, ensuring a tight seal to prevent water leaks during the wash cycle.

You should replace the outer door boot seal clamp if it becomes damaged or loses its tension, which can happen due to regular use, exposure to harsh cleaning agents, or physical wear and tear.

Symptoms of a bad outer door boot seal clamp include:

• Water leaks from the door area during the wash cycle
• Loose or shifting door boot seal
• Difficulty in closing the washing machine door securely

This OEM LG part is also compatible with Sears/Kenmore.

A balance weight that helps stabilize the washer tub during spin cycles to reduce vibration and prevent the appliance from rocking. Replaces a worn or broken cabinet weight to restore smoother, quieter operation. What it does:

• Adds mass to the washer cabinet to counteract tub imbalance during spins
• Reduces excessive vibration, shaking, and loud banging noises when spinning
• Helps prevent the washer from walking or shifting on the floor
• Works as the factory replacement for the original cabinet balance assembly

• Disconnect power and, if applicable, water supply before starting any repair
• Empty the drum and remove the required access panels per your model's service manual
• Securely fasten the weight using the original mounting hardware and torque per OEM guidance

This tub cover replaces the outer trim that surrounds the washer tub to protect internal components and provide a finished appearance. It restores a snug seal and helps keep water and debris away from moving parts. What it does:

• Covers and protects the outer edge of the washer tub to reduce debris intrusion and wear
• Helps maintain proper alignment and spacing between the tub and cabinet trim
• Restores the washer's finished appearance if the original cover is cracked, warped, or missing
• Can reduce noise caused by loose or damaged tub trim contacting other components

• One replacement tub cover

• Basic hand tools may be required; disconnect power and water before beginning
• Inspect surrounding seals and fasteners; replace any damaged clips or screws for a secure fit
• Handle carefully to avoid scratching the finish during installation

This motor wire harness links the washer's drive motor to the main control, carrying power and signal connections so the drum can start and regulate spin/tumble. Replacing a damaged harness restores reliable motor operation and helps prevent intermittent faults.

• Carries power and control signals between the main PCB and the drive motor
• Ensures secure, keyed connections at the motor and control board
• Drum won't spin or tumble, or stops mid-cycle
• Intermittent motor operation, humming, or "LE" motor error on some models
• Visible heat damage, broken wires, or loose/burned connectors

• Disconnect power before servicing; allow any capacitors on the control to discharge
• Access the harness by removing the rear or top panel per your model's service information
• Photograph routing and reuse all clips/ties; keep wiring clear of the rotor/drum and sharp edges
• Seat connectors fully (keyed plugs only fit one way); do not force, and secure all strain reliefs

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

The Washer Gasket is an OEM replacement part for LG washing machines. It is a flexible seal that lines the opening of the washer tub, creating an airtight barrier to prevent water leaks and ensure proper containment during the wash and spin cycles.

Symptoms of a bad washer gasket include:

• Water leaking from the front of the washing machine
• Excessive moisture or condensation buildup around the gasket area
• Difficulty in properly closing and latching the washer door due to a worn or damaged gasket

Causes of a washer gasket failure can range from general wear and tear over time, to physical damage from being pinched or cracked, to improper installation or alignment issues.

This OEM LG part is also compatible with Sears/Kenmore models.

Washer screw

The Motor Stator Bolt is an OEM part for LG washing machines. This bolt secures the stator to the motor, ensuring the stability and proper functioning of the washing machine's motor assembly.

Causes of a bad motor stator bolt can include wear and tear over time, improper installation, or damage from over-tightening or impact. A compromised bolt can lead to instability in the motor, potentially affecting the washer's performance.

Symptoms of a bad motor stator bolt include:

• Unusual noises during the wash cycle
• Vibrations or shaking of the washer
• The motor not functioning properly or failing to start

This OEM LG part is also compatible with Sears/Kenmore.

This is a motor harness intended for use with washing machines. The motor harness is a wiring component that's attached to the washing machine's motor and is used to conduct electricity between the motor and the PCB. Wear and tear, damage, or other issues can arise with the motor harness over time. When there is a malfunction or failure with this component, a replacement part is necessary to continue the appliance's efficient and safe use.Signs that something has gone wrong with the washing machine's motor harness include intermittent operations or a device that won't run at all. Replacing the motor harness is a relatively easy task. Disconnect the appliance from power and wear work gloves for safety. Ensure all connections between the motor and motor harness are secure before plugging the washing machine back into to avoid the motor's accidental activation.This motor harness is an authentic OEM replacement part. It is sold as an individual unit. The motor harness is made of high-quality, durable materials. It comes sourced directly from the manufacturer to ensure compatibility. The motor harness can be installed in various models of washing machines. It fits correctly into appliances produced by Kenmore and LG.

The Door Latch Hook is an OEM replacement part for LG front load washers. It is a component of the overall latch and locking assembly and works to securely close and lock the washer door. With a properly functioning latch hook, the washer door remains tightly sealed during cycles to ensure optimal water retention and the most thorough cleaning. 

Symptoms of a bad door latch hook include:

• Water leaks around the door during washing cycles
• The door fails to latch fully and unlock after cycles 
• Difficulty opening or closing the washer door completely
• Alignment issues like misaligned or skewed door positions

Causes of a bad door latch hook can include wear over extended use. Damage may also result from washing hard or abrasive items that put excess strain on the latch mechanism over time.

This OEM LG part is compatible with Sears/Kenmore front-load washer models as well. 

The Magnetic Door Plunger is an OEM part for LG washing machines. It is designed to securely hold the door in a closed position during the operation cycle, employing a magnet mechanism for enhanced reliability. The plunger ensures that the door latch is properly engaged, preventing the machine from running if the door is not closed correctly.

Causes of a bad Magnetic Door Plunger can include wear and tear from constant use, failure of the magnetic mechanism due to exposure to moisture or mechanical damage, or a misalignment that prevents the door from closing properly.

Symptoms of a bad Magnetic Door Plunger include:

• The washing machine door not staying closed during cycles.
• The machine failing to start due to a door sensor not detecting closure.
• Random pausing of the machine during operation if the door unlatches.

This OEM LG part is also compatible with Sears/Kenmore.

The Inlet Valve Assembly is an OEM part for LG washing machines. It controls the flow of water into the washing machine during different cycles, ensuring the correct amount of water enters the tub for optimal washing performance. The assembly includes solenoids that open and close the valve based on signals from the washing machine’s control board.

You should replace this inlet valve assembly if it becomes faulty or damaged. Causes of a bad inlet valve assembly can include mineral buildup from hard water, electrical faults, or wear and tear from regular use. A malfunctioning valve can lead to issues with water flow, affecting the machine’s washing efficiency.

Symptoms of a bad inlet valve assembly include:

• No water entering the washing machine
• Water entering too slowly or at an inconsistent rate
• The washing machine not filling properly
• Water leaks from the valve area

This OEM LG part is also compatible with Sears/Kenmore models.

The Water Inlet Valve Assembly is an OEM replacement part for LG washing machines, designed to control the flow of water into the laundry tub. This part is responsible for opening and closing to allow water into the wash drum at the appropriate times during the wash cycle, providing the correct water level and temperature.

Causes of a bad Water Inlet Valve Assembly can include mineral deposits blocking the valve, electrical failure preventing the valve from opening or closing properly, or physical damage to the valve mechanism itself.

Symptoms of a bad Water Inlet Valve Assembly include:

• Inadequate filling of the washer drum
• Water entering the drum when the washer is off
• Unusual noises during the fill cycle
• Water that is too hot or too cold, indicating a failure in valve operation that controls temperature

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Water Inlet Valve Filter Screen is an OEM part for LG washing machines. This filter screen is designed to fit inside the water inlet valve, ensuring that debris and sediment are filtered out before the water enters the washing machine. This helps maintain clean water flow and protects the internal components of the washing machine from damage caused by particles.

Causes of a bad Water Inlet Valve Filter Screen can include clogging due to sediment buildup, damage from high water pressure, or wear and tear over time. Regular inspection and cleaning can help prolong the life of the filter screen.

Symptoms of a bad Water Inlet Valve Filter Screen include:

• Reduced water flow into the washing machine
• Long fill times or failure to fill
• Sediment or debris found in the wash water
• Error codes related to water intake issues

This OEM LG part is also compatible with Sears/Kenmore.

The Float Assembly is an OEM part for LG washing machines. This part monitors and controls the water level within the appliance. It's a safety feature that prevents water overflow and potential flooding, contributing to the efficient operation of the washing machine by maintaining the correct water level for each cycle.

Causes of a bad Float Assembly can vary from simple blockages that prevent the float from moving freely to electrical faults within the switch mechanism. 

Symptoms of a bad Float Assembly include:

• Water overflowing from the washing machine
• Inadequate water levels that affect the washing cycle's effectiveness
• The washing machine failing to start the fill cycle due to a malfunctioning float switch

This OEM LG part is also compatible with some Kenmore models.

This base bracket mounts to the washer's lower frame to hold associated components securely in place. By keeping parts properly anchored, it helps maintain alignment and stability during operation to minimize vibration and noise.

• Attaches to the washer base and provides a mounting point for designated hardware
• Helps keep assemblies from shifting during agitation and spin
• Supports smooth, quieter operation by reducing vibration and rattling
• Common signs of failure include a bent or cracked bracket, loose/misaligned parts, or unusual noises from the base area

• Disconnect power and water supply before servicing; move the appliance for safe access
• Carefully tip or lay the washer back on protective padding; use a helper for stability
• Note the bracket's orientation and reuse existing mounting hardware as applicable
• Tighten fasteners securely and verify nearby parts have proper clearance before test run

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Fabric Softener Cap is an OEM replacement part for LG front-loading washing machines. It is a replaceable component that securely fastens into the internal dispenser drawer, containing liquid fabric softener added during wash cycles. Color: blue. It measures about 2-1/2 inches wide by 4-1/2 inches deep.

Symptoms of a problematic cap could include: 

• Softener stains or residue accumulating around base gasket seals  
• Drips or puddles indicative of compromised sealing surfaces
• Cracks, fatigue, or warping affecting secure closure 

Causes typically relate to normal plastic material breakdown after years of opening and closing cycles. Exposure to cleaning detergents could potentially deteriorate gaskets as well.

Compatible brands include Kenmore Elite and some Café laundry appliances too. 

The Bleach Funnel is an OEM part for LG washing machines. This part safely dispenses and introduces liquid bleach or other cleaning agents into the wash cycle at the appropriate time.

Causes of a bad Bleach Funnel can include physical damage, wear and tear over time, or clogs from residue buildup. 

Symptoms of a faulty Bleach Funnel include:

• Bleach or cleaning agents not being properly dispensed
• Leaks or residue buildup in the dispenser area
• Clogging or blockages preventing proper flow
• Washing machine not effectively utilizing bleach or cleaning additives

This OEM LG part is also compatible with some Kenmore models.

The Detergent Box Assembly is an OEM replacement part for LG washing machines. This assembly is responsible for holding and dispensing detergent and other laundry additives during the wash cycle. It ensures that the correct amounts of detergent, bleach, and fabric softener are released at the appropriate times, contributing to effective cleaning and care of your clothes.

Over time, the detergent box assembly can become worn out or damaged due to continuous exposure to water and detergent. Buildup of detergent residues can clog the compartments, and the mechanical parts of the assembly can also degrade. 

Symptoms of a bad detergent box assembly include:

• The detergent, bleach, or fabric softener not dispensing properly
• Visible cracks, warping, or damage to the box
• Residues remaining in the compartments after a wash cycle
• Leaks from the detergent box area
• Error messages related to dispensing issues

This OEM LG part is also compatible with some Sears/Kenmore washing machine models.

This inlet hose routes household water into the appliance so it can fill and operate correctly. Replacing a damaged inlet hose restores proper water flow and prevents leaks that can cause poor performance or water damage. What it does:

• Channels incoming water from the household supply into the appliance
• Stops leaks and restores normal fill when the original hose is cracked, split, or worn
• Helps correct symptoms like no water entering the appliance, slow or intermittent fill, or visible leaking at the hose connection
• Works with the appliance's valve and fittings to maintain a sealed water path

• Turn off the water supply and unplug the appliance before starting any work
• Inspect fittings and seals; replace any worn gaskets to ensure a watertight connection
• Hand-tighten connections then check for leaks; avoid overtightening plastic fittings

The Dispenser Assembly is an OEM part for LG front-loading washers. It is responsible for dispensing detergent and fabric softener at the appropriate times during the wash cycle. The dispenser assembly contains separate compartments for detergent and fabric softener, as well as timed mechanisms that release each additive when needed for cleaning and softening results.

Causes of a bad dispenser assembly can include issues with the dispensing mechanisms like clogging, jamming, or malfunctions preventing the timely release of detergent and softener. Damage to compartment seals or lids could also cause improper dispensing.

Symptoms of a bad dispenser assembly include:

• Residue or buildup of detergent in the drum or tub
• Strong detergent or fabric softener odors that won't come out of clothes
• Dispenser drawers, lids, or seals that do not close or lock securely

This OEM LG part is also compatible with Sears/Kenmore.

This part may be black or gray in color.

The Dispenser Hose is an OEM part for LG washing machines. It connects the detergent dispenser to the washer tub, allowing detergent and other cleaning agents to be delivered effectively during the wash cycle.

Causes of a bad dispenser hose can include regular wear and tear, damage from harsh detergents, or physical damage due to kinks, pinches, or impact. Over time, the hose can become brittle, cracked, or clogged, affecting its ability to function properly.

Symptoms of a bad dispenser hose include:

• Leaks or drips from the hose area
• Detergent not dispensing correctly or at all
• Water pooling around the washer
• Visible cracks or splits in the hose

This OEM LG part is also compatible with Sears/Kenmore models.

The Vent Hose is an OEM part for LG washing machines. This hose is essential for ensuring proper ventilation within the washer, allowing air to circulate and preventing the buildup of moisture and mildew. It helps maintain the efficiency of the washing machine by facilitating the expulsion of air and excess water vapor during operation.

Causes of a bad washer vent hose can include wear and tear over time, blockages from lint or debris, or damage due to bending or pinching.

Symptoms of a bad vent hose include:

• Excessive moisture or condensation inside the washer
• Musty odors from the washing machine
• Visible cracks or holes in the hose
• Poor ventilation leading to inefficient washing cycles

This OEM LG part is also compatible with Sears/Kenmore.

Includes sensor probe

This inlet hose carries supply water into the washer during the fill cycle. Replacing a worn or leaking hose restores proper water flow and helps prevent leaks and fill errors that can leave clothes unwashed or floors wet.

• Channels incoming water from the inlet valve into the washer
• Maintains a sealed connection to prevent drips and leaks
• Replaces hoses that are cracked, swollen, kinked, or clogged with mineral deposits
• Common symptoms: water leaking during fill, reduced water flow or fill error codes, visible cracks/splits

• Disconnect power and turn off both water supply valves before servicing
• Keep towels or a container handy; residual water may spill when removing hoses
• Note hose routing; fully seat ends and secure with existing or new clamps as required
• Restore water and power, then run a quick fill to check all connections for leaks

This inlet hose routes incoming water from the washer's fill valve into the machine to support proper filling. Replace a cracked or leaking hose to stop drips, prevent water damage, and restore reliable fill performance.

• Directs incoming water from the fill valve to the dispenser/tub during wash cycles
• Maintains a sealed path to prevent internal or external leaks
• Helps the washer reach proper fill levels and timing
• Common symptoms of failure: water on the floor, leaks during fill, visible cracks or bulges, long/no fill or IE error

• Unplug the washer and turn off both hot and cold water supplies
• Keep towels or a pan handy; relieve residual water pressure before disconnecting
• Note the original routing; fully seat the hose on fittings and secure with existing clamps
• Restore water and power, then run a quick fill to check for leaks

This hose connector joins a refrigerator's/dispenser's water line to internal plumbing, restoring a secure, leak-resistant connection. It replaces cracked or worn connectors to help stop leaks and ensure reliable water flow. What it does:

• Provides a sealed connection between the water hose and the appliance plumbing or valve
• Stops leaks caused by cracked, brittle, or damaged connectors
• Restores proper water flow to the dispenser/ice maker when the connector is the failure point
• Works with hose clamps or fittings already present in the appliance plumbing

• Shut off water supply and unplug the appliance before servicing
• Inspect hose ends and replace clamps or O-rings if damaged; use proper-size clamps for a secure fit
• Hand-start threads, then tighten snugly—avoid over-tightening plastic fittings to prevent damage
• Turn water back on and check thoroughly for leaks after installation

The Drain Pump and Motor is an original LG (OEM) replacement part for LG made washing machines that is responsible for removing water from the washer at the end of the wash cycle. The pump forces water out through the drain hose so that clothing comes out free of excess water, making the drying process faster. 

Symptoms of a failing Drain Pump Motor include:

• Water not draining out of the washing machine 
• Noisy or unusual sounds coming from the pump area during the drain cycle
• The washing machine stopping mid-cycle

Causes of a bad Drain Pump Motor can range from obstructions in the pump or hose, which can strain or damage the motor, to wear and tear from regular use leading to motor failure. Electrical issues can also affect the motor's performance, preventing it from operating correctly.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Drain Hose is an OEM part for LG washing machines. It is designed to carry used water from the washing machine to the household drain. This hose ensures that water is efficiently expelled from the washer, preventing any overflow or leakage issues.

Causes of a bad drain hose can include cracks or splits due to wear and tear, clogs from debris or residue buildup, and damage from mishandling or improper installation. Such issues can compromise the hose's ability to transport water effectively.

Symptoms of a bad Drain Hose include:

• Water leaks during or after the wash cycle
• The washer not draining properly
• Visible cracks or damage to the hose
• Unpleasant odors due to trapped debris or standing water

This OEM LG part is also compatible with Sears/Kenmore models.

Does not come with a hose or filter. These have to be purchased separately

The Washer Circulation Pump Motor is an OEM replacement part for LG washing machines. It is a vital component responsible for circulating and pumping water through the wash tub during the various wash and rinse cycles.

Symptoms of a faulty circulation pump motor include:

• Improper water circulation or agitation during wash cycles
• Failure to drain or drain slowly after wash cycles
• Abnormal noises or vibrations coming from the pump area

Causes of a bad circulation pump motor can range from normal wear and tear over time, electrical malfunctions, blockages or obstructions in the pump impeller, or physical damage from foreign objects or debris.

This OEM LG part is also compatible with Sears/Kenmore washing machine models.

The Pump Filter Assembly is an OEM replacement part for LG washing machines. It is a crucial component that filters out lint, debris, and other particles from the wash water, preventing them from recirculating and damaging the pump or other internal components.

Symptoms of a need to replace the pump filter assembly:

• Clogging or blockages, leading to poor drainage or water not draining completely
• Excessive buildup of lint, hair, or other debris in the filter screen
• Leaks or water seeping from the filter housing or surrounding area
•  Unusual noises or vibrations during the drain or spin cycles, indicating a potential blockage

Causes of a faulty pump filter assembly can include excessive lint accumulation, damage to the filter screen or housing due to impact or mishandling, and general wear and tear over time.

This OEM LG part is also compatible with Sears/Kenmore washing machines.

The Damper is an OEM replacement part for LG washing machines. It plays an important role in regulating airflow through the machine's drying system. The damper uses adjustable louvers to direct warm air emitted during the drying cycle. 

Causes of a faulty washer damper include broken internal mechanisms preventing louver movement, and restricting optimal air dispersion. Dust or mineral buildup can also impact function over time.

Symptoms of a problematic damper are

• incomplete or lengthy drying cycles.
• Clothing may still feel damp even after an extended run
• Excessive lint accumulation could also point to improper air management

This OEM LG part is also compatible with Sears/Kenmore.

The Common Bolt is an OEM part for LG washing machines. It is a necessary mounting hardware component used to securely fasten and assemble various internal parts and components. Common bolts play a crucial role in ensuring the washer maintains solid construction and can withstand the shaking and vibrations of each wash cycle.

Causes of a bad common bolt can include stripped threads, rust, or damage over time due to repeated use or exposure to detergents and chemicals.

Symptoms of a bad common bolt include:

• Loose or detached internal parts
• Excessive noise or vibration
• Leaks around seal areas

This OEM LG part is also compatible with some Kenmore models.

This is the direct-drive rotor for the dishwasher wash motor. It pairs with the stator to spin the impeller and circulate wash water through the spray arms, helping restore proper spray pressure and quieter operation when the original rotor is worn.

• Couples with the stator to drive the circulation pump impeller
• Moves wash water through the spray arms for consistent cleaning performance
• Common failure signs: little or no spray, poor cleaning, loud humming or grinding from the pump area, or intermittent wash action
• Physical damage or weakened magnets can prevent proper rotation

• Disconnect power and water supply and pull the unit forward for access
• Remove the toe-kick and drain remaining water at the sump
• Remove the pump cover and center fastener, then pull the old rotor straight off
• Seat the new rotor fully, reassemble, and run a test cycle to check operation and leaks

This water level pressure switch senses the washer tub's water level and signals the control to start or stop filling. It restores accurate fill detection for proper wash cycles and helps prevent overfilling or improper operation. What it does:

• Detects water level via a vacuum hose and tells the control board when to stop filling
• Helps prevent overfill, underfill, and related cycle interruptions
• Can resolve symptoms like washer not filling, overfilling, or stopping mid-cycle
• Works as the sensing interface between the tub and the control system

• One water level pressure switch assembly

• Disconnect power and shut off water supply before replacing the part
• Note the vacuum hose routing and electrical connector locations before removal
• Handle the small vacuum hose and plastic fittings gently to avoid damage or air leaks

The Suspension Spring is an OEM part for LG washing machines, specifically designed to support the tub assembly and maintain its stability during the wash and spin cycles. This spring plays a critical role in absorbing vibrations and reducing the amount of movement transferred to the washing machine's frame, ensuring smooth and quiet operation. 

Causes for a Suspension Spring to fail include normal wear and tear from repeated use, overloading the washing machine beyond its capacity, which can stretch or stress the springs, and corrosion from exposure to moisture and laundry detergents. 

Symptoms of a bad Suspension Spring include:

• Increased vibration and noise during the spin cycle.
• The washing machine "walking" or moving from its original position.
• Uneven drum movement, leading to inconsistent washing and spinning.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Suspension Spring Holder is an OEM part for LG washing machines. This holder supports the suspension springs that help stabilize the washer drum during operation, reducing vibration and movement. It plays a critical role in ensuring smooth and quiet operation of the washing machine.

Over time, the suspension spring holder can become worn or damaged due to regular use, heavy loads, or accidental impacts. Causes of a bad suspension spring holder include wear and tear, physical damage, or corrosion from moisture exposure.

Symptoms of a bad suspension spring holder include:

• Excessive vibration or shaking during wash cycles
• Unusual noises, such as banging or clunking
• The washer drum appearing misaligned or sagging
• The washing machine moving or walking during operation

This OEM LG part is also compatible with Sears/Kenmore.

This power cord assembly restores a secure electrical connection to your appliance so it can safely receive power. It replaces a worn, damaged, or faulty cord to help prevent interruptions and poor contact during normal use. What it does:

• Re-establishes the appliance's main power connection for reliable operation
• Replaces frayed, burnt, or damaged cord insulation and terminals
• Can stop intermittent power loss, sparking, or poor contact at the cord connection
• Provides the correct OEM-fit electrical cord and connector interface

• Always disconnect power at the breaker or unplug the appliance before starting work.
• Tighten terminal screws securely and avoid pinching or kinking the cord.

The Drain Hose Assembly is an OEM part for LG washing machines. It is a component designed to transport used water from the washer to the drain. This flexible hose assembly ensures that water flows smoothly out of your washing machine after each cycle, preventing leaks and maintaining the efficiency of your appliance. 

Causes for replacement can include wear and tear over time, clogs from lint or small items, kinks that restrict water flow, or damage from moving or improper installation. 

Symptoms of a bad Drain Hose Assembly include:

• Water leaking from the back or bottom of the washing machine
• Difficulty draining water out of the washer
• Puddles of water forming around the appliance during or after operation

This OEM LG part is also compatible with some Kenmore models.

This pivot hanger assembly supports and stabilizes the appliance component it mounts to, restoring smooth movement and alignment. Replace a worn or damaged pivot to reduce noise and prevent misalignment that can affect operation. What it does:

• Acts as the pivot point for the hanger to support the drum/door assembly and maintain correct alignment
• Helps eliminate squeaks, scraping, or jerky motion caused by a worn pivot
• Prevents sagging or uneven movement that can lead to rubbing or binding
• Restores proper mechanical support so the appliance operates quietly and reliably

• Unplug the appliance or disconnect power before beginning any repair
• Basic hand tools may be required; follow the appliance service manual for disassembly steps
• Inspect surrounding components (mounts, bearings, fasteners) and replace if worn

The Washer Door Lock Switch is an OEM part for LG washing machines. This critical safety feature locks the washer door during operation to prevent it from being opened, which ensures safety and proper functioning. The door lock switch also communicates with the washer's control system to indicate that the door is securely closed and the machine can begin its cycle.

Symptoms of a bad Washer Door Lock Switch include:

• The washing machine refusing to start, despite the door appearing to be closed.
• The door failing to lock properly, or the lock releasing prematurely during a cycle.
• Error messages on the washer's display related to door closure issues.

Causes of a bad door lock switch can include mechanical failures such as worn or damaged locking mechanisms, electrical issues like faulty wiring or failed solenoids, or alignment problems that prevent the door from engaging the switch properly.

This OEM LG part is also compatible with Sears/Kenmore models.

This spring-style hose clamp secures a washer's rubber hose to its fitting to maintain a tight, leak-resistant seal. Replacing a weakened clamp helps stop drips and keeps the hose firmly in place during operation.

• Provides constant spring tension to hold a rubber hose on its port
• Helps prevent leaks at the connection point
• Resists vibration so the hose doesn't back off the fitting
• Common signs include water at a hose joint, a loose/detached hose, or a rusted/broken clamp

• Disconnect power and turn off water supply before servicing
• Place a towel or pan to catch residual water from hoses
• Use pliers to compress the ears, slide off the old clamp, position the new clamp behind the hose bead, and release evenly
• After reassembly, run a quick test cycle and check for leaks

This protective cover shields internal components and wiring from dirt, moisture and accidental contact, helping keep the appliance safe and functioning properly. It's a small replacement panel that restores the appliance's factory protection. What it does:

• Covers and protects internal parts and wiring from debris and accidental impact
• Prevents loose components from rattling or shifting during operation
• Helps maintain proper spacing and alignment of nearby panels and clips
• Addresses symptoms like visible damage, missing cover, exposed wiring, or unusual noise from loose trim

• Disconnect power before starting any repair to avoid shock or injury
• Typically secures with clips or a few screws; use basic hand tools and take care not to strip fasteners
• Inspect mounting tabs and surrounding trim for damage; replace any broken clips before reassembly

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.

Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.

Symptoms of a bad clamp include:

• Water leaking from hose connections
• Hoses coming loose or detaching during operation
• Visible rust or damage on the clamp
• Poor water flow or pressure issues

This OEM LG part is also compatible with Sears/Kenmore models.

This hose clamp secures a rubber hose connection to prevent leaks where the hose meets its fitting. A tight, uniform seal helps maintain proper water flow and keeps the appliance operating reliably.

• Provides a tight, 360-degree seal around the hose barb/fitting
• Helps correct issues like water leaks at the hose connection point
• Maintains correct hose attachment during operation and vibration
• Step-less ear design distributes clamping force evenly

• Unplug power and shut off water supply before servicing
• Note clamp orientation and hose routing before removal
• Use appropriate ear-clamp pincers or pliers to compress the clamp evenly
• Check the hose and fitting for wear; replace if cracked or deformed

This hose clamp secures a washer hose to its fitting to maintain a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop seepage at hose joints and keep the washer operating reliably.

• Holds the hose firmly on pump, tub, or drain fittings to help prevent leaks
• Maintains clamping pressure during operation and vibration
• Replace if rusted, bent, cracked, or no longer holding tension
• Typical symptoms: water dripping at hose connections or a hose that slips off

• Disconnect power and shut off water; drain any remaining water from the unit
• Release and slide back the old clamp, then remove the hose
• Fully seat the hose on the fitting and position the clamp just behind the hose bead/ridge
• Secure the clamp and run a brief test to check for leaks

The Noise Filter Assembly is an OEM part for LG washing machines, designed to minimize electrical noise interference within the appliance. This essential component ensures that the washer operates smoothly without emitting disruptive sounds that can affect both the performance of the washer and the comfort of your home environment. 

Causes of a bad Noise Filter Assembly can range from wear and tear over time to exposure to power surges or electrical spikes, which can damage the internal components of the filter. 

Symptoms of a bad Noise Filter Assembly include:

• Increased electrical noise or buzzing sounds emanating from the washer
• Intermittent disruptions in the washer's performance
• The washing machine failing to start or experiencing power fluctuations

This OEM LG part is also compatible with some Kenmore models.

The Gasket is an OEM part for LG washing machines. This part forms a seal around the washer door, preventing water from leaking out during wash cycles.  

Causes of a bad gasket can include continuous exposure to water and detergent, mold or mildew buildup, and wear and tear from frequent opening and closing of the washer door. 

Symptoms of a bad gasket include:

• Water leaking from the washer door during operation
• Visible cracks, tears, or deformities in the gasket
• Mold or mildew buildup on the gasket
• The door not sealing properly, leading to inefficient washing

This OEM LG part is also compatible with some Kenmore models.

This nozzle connector links a water hose to the washer's nozzle/dispenser assembly, creating a tight, leak-resistant connection. Replacing a worn connector helps stop leaks and restores consistent water flow during fill and spray functions. What it does:

• Couples the hose to the nozzle/dispenser assembly and maintains a watertight seal
• Directs water into the dispenser or tub as designed
• Typical failure symptoms: leaks near the top panel or dispenser, loose hose, weak or erratic spray/fill
• Cracking, hardening, or deformation can lead to drips and connection issues

• 1 nozzle connector

• Disconnect power and shut off water supplies before servicing
• Remove the top cover to access the dispenser/nozzle area; protect the work area with a towel
• Release hose clamps, seat the hose fully on the new connector, and secure clamps firmly
• Run a brief fill/rinse to check for leaks before reassembly

A molded water guide that routes dispenser water inside the refrigerator to the dispenser/ice area, helping direct flow and reduce splashing. Fits the factory mounting points for a clean, secure path for water. What it does

• Channels water from the inlet tubing toward the dispenser/ice assembly to prevent misdirected flow.
• Helps keep water from pooling or dripping inside the cabinet or on internal components.
• Common replacement when you see water on shelves, puddling near the dispenser, or reduced or misdirected dispenser flow.
• Preserves proper alignment of the dispenser plumbing to prevent kinks or strain on tubing.

• One water guide (single molded channel) as shown.

• Turn off the refrigerator and shut off the water supply before starting; disconnect power for safety.
• Remove interior panels or shelves as needed to access mounting points; keep fasteners for reassembly.
• Inspect adjoining tubing and seals for damage and replace any worn components to ensure a leak-free fit.
• After installation, restore power and water, then check carefully for leaks during an initial test dispense.

The Tub to Pump Hose is an OEM replacement part for LG top-load washing machines. This hose safely transports water between the wash tub and drain pump. The hose measures 13 inches in length.

Causes of failure relate to constant flexing under water pressure strains that accumulate over years of usage. Excess minerals in hard water areas promote accelerated breakdown of flexible PVC material.

Symptoms of a cracked or leaking tub to pump hose include: 

• Water not draining or taking an abnormally long time
• Water continually accumulating inside the machine cabinet   
• Error codes related to drainage issues displayed  
• Puddles forming near or under the back of the washer

This genuine LG hose is also compatible with select Sears/Kenmore units as well.

The Inner Door Boot Seal Clamp is an OEM part for LG washing machines. The clamp's primary function is to secure the door boot seal in place, preventing leaks during the wash cycle. 

Causes of a bad Inner Door Boot Seal Clamp can include corrosion due to exposure to moisture and detergent, loss of tension over time, or physical damage which can lead to a compromised seal.

Symptoms of a bad Inner Door Boot Seal Clamp include:

• Water leaking from the front of the washing machine
• Visible rust or damage on the clamp
• The door boot seal coming loose or falling off

This genuine LG OEM replacement part is also compatible with some Kenmore models. 

The Air Chamber is an OEM part for LG washing machines. This part connects to the pressure switch and ensures the washer machine fills with the correct amount of water for the selected cycle. 

Causes of a bad  Air Chamber can include clogging due to detergent residue or debris, cracks or perforations that lead to air leaks, and aging of the material, which might compromise its integrity and function.

Symptoms of a faulty Air Chamber include:

• Inaccurate water level readings leading to overfilling or insufficient water during cycles
• Unusual noises during the fill cycle, indicating air escaping
• The washing machine failing to start the wash cycle due to improper water level detection
• Error codes displayed on the machine that relate to water level issues

This OEM LG part is also compatible with some Kenmore models.

This inlet hose delivers fresh water from your home supply to the appliance, restoring proper fill and preventing leaks. It's a direct-fit replacement designed to restore normal water flow and stop visible hose damage. What it does:

• Channels water from the household supply into the appliance's inlet valve
• Replaces cracked, split, or leaking inlet hoses that allow water to escape
• Helps resolve symptoms like weak/no fill, visible dripping at the connection, or intermittent water flow
• Matches OEM routing and connection points for a proper seal when installed correctly

• Turn off water supply and unplug the appliance before starting
• Inspect fittings and replace any damaged seals or washers as needed
• Hand-tighten connections and finish with a quarter turn; avoid overtightening to prevent damage
• Run a short test fill and check all connections for leaks before returning the appliance to service

The Hose is an OEM part for LG washing machines. This component is crucial for the proper flow of water into and out of the washing machine, ensuring efficient washing and rinsing cycles. The hose is designed to withstand high water pressure and regular use.

Causes of a bad hose can include wear and tear over time, exposure to harsh water conditions, or accidental damage such as kinks or punctures. Ensuring the hose is in good condition is essential to prevent leaks and maintain optimal water flow.

Symptoms of a bad hose include:

• Water leaks around the hose connections
• Reduced water flow into or out of the washing machine
• Visible cracks, bulges, or kinks in the hose

This OEM LG part is also compatible with Sears/Kenmore.

This hose connector joins two internal water lines inside your washer to create a secure, leak-resistant connection. Replacing a worn coupler helps stop drips and keeps water moving properly during fill, wash/recirculation, and drain cycles.

• Joins two hoses inside the appliance for a tight, reliable seal
• Helps maintain proper water flow during operation
• Replace if cracked, deformed, or if hoses slip off despite clamp tension

• Unplug the washer and turn off water supply; expect some residual water
• Access the hose junction and note hose routing and clamp positions
• Fully seat hoses onto the connector and secure clamps behind the hose bead
• Reassemble and run a short test cycle while checking for leaks

The Washing Machine Shock Absorber Kit is an OEM part for LG washing machines. This kit includes a shock absorber designed to reduce vibrations and absorb shocks during the wash cycle, providing stability and minimizing excessive movement. 

Over time, the shock absorbers can wear out due to regular use, exposure to heavy or unbalanced loads, or damage from impact. These factors can lead to reduced effectiveness of the shock absorbers, causing increased vibrations and noise.

Symptoms of a bad shock absorber kit include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging or thumping noises
• The washer moving or "walking" during operation
• Leaks due to increased stress on the tub and other components

This OEM LG part is also compatible with Sears/Kenmore.

The Hinge Pin is an OEM part for LG washing machines. It serves as a pivot point for the washer door, allowing it to open and close smoothly. This component is crucial for maintaining the proper alignment and function of the washer door, ensuring a secure and reliable seal during operation.

Common causes of a bad hinge pin include frequent use leading to wear and tear, physical damage from accidental impacts, or rust and corrosion over time. A compromised hinge pin can result in misalignment of the door, affecting the washing machine's ability to close properly and maintain an effective seal.

Symptoms of a bad hinge pin include:

• Difficulty opening or closing the washer door
• Door not staying securely closed during operation
• Squeaking or grinding noises when the door is moved
• Visible wear or damage to the hinge pin

This OEM LG part is also compatible with Sears/Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.