Washer Valve

• Will not stop filling with water
• Leaking
• Shuts off too soon
• Will not fill with water

Replaced the cold water valve unit (has 4 ports and 1 inlet) which is very straight forward; requires : 1 phillips screwdriver ~#2 1 needlenose plier, medium size 1 channel lock plier, medium size 1 marker pen 1 - cold water valve assembly # AP4445613 1 - hot water valve assembly #AP4441935 1 - water level pressure switch #AP4440713 an old towel or two for absorbing small amounts of water a cellphone / camera for making sure you have the... Read more

I removed the top of the washer, disconnected the existing inlet valve assembly, and replaced it with the part I bought from AppliancePartsPros.com. If it hadn't taken me 30 minutes to figure out how to remove the top of the washer (not the entire top, just the cover over the control panel area), this would have been a 5 minute repair. Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water
• Fills and drains at the same time

I watched the how-to video on your website to learn how to get at the valve to replace it. Before watching the video, I did not know how to take the washer cabinet apart to replace the valve. I searched on your website for my washer model, but the exact model number was not listed. I chose a very similar model number and looked up the info for that machine's replacement valve . It looked like it would work in my washing machine so I decided to take a chance and order the valve. I placed my... Read more

So this is a good one - a tale of outstanding technical and customer support, mingled with some ridiculous shipping fiascoes - read on! I called the tech team, who helped me to correctly diagnose that my constantly running cold water was caused by the shut-off assembly and not the board - great, as that is cheaper. Sincere thanks to the tech people! So I ordered the part, with expedited shipping. Amazingly it arrived the next day! But it was damaged in shipping as the warehouse has just stuffed... Read more

• Will not stop filling with water
• No hot or cold water
• Will not fill with water

Replacing the water inlet valve fixed the problem. For many months we noticed cold water was just dribbling into the washer during the rinse cycle, and "warm" washes were hot not warm. It seemed like the cold water wasn't able to enter the machine. Then one day the cycle just stopped when it reached "rinse" and wouldn't go any further. I first tried solving it by cleaning the filter where the cold water hose enters the machine at the back. It was coated in sediment (the water comes from a... Read more

Replaced solenoid valve assembly. Easy repair. Read more

• Will not fill with water
• Shuts off too soon
• Noisy

Conducted research on web, and via direct contact with AppliancePros where a diagnosis of replacing the water inlet valve and cleaning the sensor tube would "most probably" (80%) handle the issue. The remaining uncertainty would reside in the electronic board circuitry. The price of replacing the water inlet valve was half of a local repair call just to diagnose the issue so I decided to have faith in the odds presented to me. The part arrived on time, and using AppliancePros advice and... Read more

After a few internet searches, it became clear that the most common fix for this issue is replacing the water inlet valve. My washer is about five years old, which aligns with the typical lifespan of these valves. I ordered the OEM parts for this washer, as this is not something you want failing and potentially flooding your home while you’re away. The thermistor is installed directly into the valve and uses an O-ring that is known to degrade and leak over time. Since the thermistor has to be... Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water

I replaced the supply lines and mesh in-line filters. I made sure incoming water pressure was strong. I also cleared some debris from the internal drain filter down below. The F20 persisted. My plan was to start swapping out parts from the inlet on. I ordered the valve and got it in a day. Thanks to the schematics and videos on appliancepartspros.com, I was comfortable with the repair, and had confidence in my plan. The actual valve replacement took about 10 minutes. Bingo bango... Read more

I had an authorized Whirlpool service tech come to look at problem diagnosed problem as water inlet valve leaking ordered the part. After 11 days I was told part was on backorder from Whirlpool. I ordered the part from you and received the next day and I installed it in approximately 20 minutes. Read more

Ordered new valve assembly, part arrived 2-3 days, installed part same day it arrived. Some difficulty getting to the two screws holding it in due to small area to work. Once that was figured out, reinstall went very smoothly, total time about one hour. Probably saved a couple of hundred if I had to hire a plumber to fix it, plus the parts. Very satisfied with the service. Read more

• Will not drain

I ordered a new pump on this website. They provided me with written directions as well as a video to follow along with on how to change the pump. As always it wasn't as easy as the video, but that was the mechanic no the tool! Great job on the service. Will order parts from here again. Read more

Ordered the valve body from Appliance Parts Pro. It was very easy to find the part on their website. Ordering was simple. The part actually got here the next day. I received an email about 2 hours after I received the part that contained the tracking number. That is what is known as quick and reliable service. Part was a little hard to replace since I have big hands. There are 2 metal screws that hold the valve body to the washer that are in a small confined area. Unless you want to dismantle... Read more

Replaced the cold water valve unit (has 4 ports and 1 inlet) which is very straight forward; requires : 1 phillips screwdriver ~#2 1 needlenose plier, medium size 1 channel lock plier, medium size 1 marker pen 1 - cold water valve assembly # AP4445613 1 - hot water valve assembly #AP4441935 1 - water level pressure switch #AP4440713 an old towel or two for absorbing small amounts of water a cellphone / camera for making sure you have the... Read more

• No hot or cold water
• Will not stop filling with water

I unplugged the machine. I removed the two fill hoses. I removed the top of the washer case by removing 3 tamper proof screws from the back ( I used my set of "star" head drivers), sliding the top back 1 inch and lifting the top off. I marked the 4 wires with 1 thru 4 stripes with a marker for ID, then pulled the 4 wires off the landing terminals. I removed the mounting screw and lifted the valve up as far as the hose permitted to get a better grip on the valve and hose. I removed the... Read more

Researched error code and symptoms on Internet. Disassembled washer back to get right part #, be careful they are different! Googled part # for OEM part, found AppliancePartsPros with competitive pricing and fast delivery, placed order on Wednesday, had it on Friday for a few bucks more. Got the part as expected, replaced, tested and success! No error code, fast wash cycle, happy better half! Read more